Introduction of Air Compressor Parts

Air Compressor Parts

Air compressor parts is a general term, air compressor is divided into piston air compressor and screw air compressor according to the working principle. Air compressor parts are mainly some regular wearing parts, screw type air compressor parts are divided into wearing parts, such as temperature sensor, pressure sensor, computer board, relay board, plc controller, control panel, operating surface box, solenoid valve, rotary valve, pneumatic valve, relief valve, temperature control valve, thermal control valve, temperature control valve spool, proportional valve, tolerance valve, pressure maintenance valve, inlet valve, safety valve, regulating valve. Switch, air duct, starter disk buffer, etc. Screw air compressor is different from piston air compressor, the working principle of screw air compressor is different from piston air compressor, the design is different, screw machine air compressor wearing parts are oil filter, air filter, oil and gas separator, oil, etc.

Product Introduction

Durable parts include cylinder body, cylinder head, seals, brakes, oil pumps, safety valves and so on, while the screw air compressor is different from the piston air compressor, the working principle of the screw air compressor is different from the piston air compressor, the design is different, the screw machine air compressor wearing parts are oil filter, air filter, solenoid valve, oil and so on, the general screw machine air compressor screw is not easy to damage, the service life is longer.

MyMRO is a compressor parts store, if you have any purchase needs you can go to our online store to shop.

Accessories Classification

1. Sensor: temperature sensor, pressure sensor.
2. Controller: computer board, relay board, plc controller, controller, control surface box, operation surface box.
3. Valves: solenoid valve, rotary valve, pneumatic valve, relief valve, temperature control valve, thermal control valve, temperature control valve spool, proportional valve, pressure maintenance valve, air inlet valve, safety valve, adjustment valve, expansion valve, expansion valve, check valve, shuttle valve, line filter, automatic drain valve, water filter cup, pressure reducing valve, pressure regulator.
4. Filter and oil: air filter, oil filter, oil fine, lubricating oil, pipeline filter, automatic drain valve, water filter cup.
5. Mainframe -: mainframe (head), bearings, shaft seal, oil seal, bushings, gears, gear shaft, overhaul.
6. Maintenance kits: mainframe, unloading valve maintenance kit, pressure maintenance valve, rotary valve, temperature control valve spool, air inlet valve, coupling elastomer and other maintenance kits.
7. Cooling: fan, radiator, heat exchanger, oil cooler, rear cooler.
8. Switch: pressure switch, temperature switch, emergency stop switch, differential pressure switch.
9. Transmission: coupling, elastomer, plummer pad, elastic block, gear, gear shaft.
10. Hose: air inlet hose, high pressure hose.
11. Starter plate: contactor, thermal protection, reverse phase protector, wire row, relay, mutual inductor, etc.
12. Buffer parts: shock pad, expansion joint, expansion valve, elastomer, plummer pad, elastic block.
13. Instrument: timer, temperature switch, temperature monitor, pressure gauge, pressure reducing gauge.
14. Motor: permanent magnet motor, inverter motor, motor, motor.

Safety Precautions

1. Operation, repair and maintenance of air compressor parts must be carried out by qualified personnel.
2. The compressor must not be reversed. After the initial start-up or electric control system overhaul, you must first confirm whether the direction of motor rotation is consistent with the prescribed steering before starting the compressor.
3. When disassembling high temperature components, wait until the temperature has cooled to ambient temperature before proceeding.
4. It is recommended to use special oil for screw compressors. It is not allowed to mix different grades of lubricants.
5. Do not make any changes or add any devices to the compressor that affect safety or reliability without the manufacturer's permission.
6. The original equipment of the compressor is specially designed and manufactured, and it is recommended to use genuine spare parts to ensure the reliability and safety of the compressor.
7. Absolutely no blockage of the compressor suction port is allowed during operation.
8. Unless it has been indicated that it can be used for breathing, it is absolutely not allowed to use the compressed air for breathing.
9. Do not run the compressor under the condition of exceeding the specified pressure and temperature.
10. Once the compressor is found to be working abnormally, the compressor should be stopped immediately and the abnormality should be eliminated in time.
11. Use the correct tools to maintain and repair the compressor.
12. Make sure all safety devices have been reinstalled and tools have been removed from the compressor after maintenance and before starting the machine.